- per page
THIS ITEM IS OUT OF STOCK.
,The D-506; "Sand Auger" ( For 2" Sch. 40 Pipe, ( 2-1/16" Inside diameter )), mounts in the inside of the dock pipe and stabilizes it firmly to the lake bottom for added dock stability and support. These are not the lightweight / breakable Aluminum ones, these are made of Solid Cast Iron, weighing over 4 lbs. each.
NOTE: THIS ITEM SUBJECT TO A MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINIMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION & INFO. ON AUGER SCREWING WRENCH )
"Inside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie inside corner of 2 dock sections together & stabilize inside corner of both sections. Same parts as D-441; "Outside Corner Angle Tie" ( Shown Above ), but Pipe Sleve is welded to the inside of the formed corner piece.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Outside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie corner of dock end section together & stabilize a floating end section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Dock Ramp Roller Assembly" is used on end of Hinged Ramps to allow end of dock ramp to roll on other dock section or shore when Floating Dock height changes.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"T-Section Connector" ( 1 ea. Male & 1 ea. Female Connector Bracket, set also includes 1 ea. hitch pin & 1 ea. hitch clip ). Use to connect 2 floating dock sections together. 2 sets required to connect 2 sections together.
NOTE: If using D3-442; "Backing Plates" OR D-561; "Fastener Kits" with the D3-420, you need 2 of either one per 1 ea. D3-420; "T-Section Connector"!!
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Corner Tie Section Connector" ( 1 ea. Male & 1 ea. Female Connector Bracket, set also includes 1 ea. hitch pin & 1 ea. hitch clip ). Use to connect 2 floating dock sections while also tying together corners of the dock sections. 2 sets required to connect 2 sections together.
NOTE: If using D3-435; "Inside Corner Supports" OR D-561; "Fastener Kits" with the D3-430, you need 2 ea. D3-435 or 4 ea. D-561 per 1 ea. D3-430; "Corner Tie Section Connector"!!
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Dock Ramp Hinge Kit" ( for Straight-Layout Ramp ), is used for the first dock section ( RAMP ) when the shore level is higher or lower than the main dock or when useing a ramp to transition from one dock level to another. Kit includes 4 ea. Hinge Plates & 2 ea. Hinge Bolts W/ Nuts.
For D3-480-1A; Ramp Hinge Kit, for L-Layout Ramp ( CLICK HERE ) to see.
For D3-480-2A; Ramp Hinge Kit, for T-Layout Ramp ( CLICK HERE ) to see.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,The D3-480-1A; "Dock Ramp Hinge Kit" for L-Layout Ramp, is used when the Dock Ramp ( or Hinged Section ) is narrower then the section it is mounted to, but will be mounted even on the right or left side of the adjoining section ( Thus making a L-Layout ). Ramp Kit comes w/ 3 ea. Straight plates & 1 ea. Formed plate, hinge bolts with nuts.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,The D3-480-2A; "Dock Ramp Hinge Kit" for T-Layout Ramp, is used when the Dock Ramp ( or Hinged Section ) is narrower then the section it is mounted to & will NOT be mounted even on the right or left side of the adjoining section ( Thus making a T-layout ). Ramp Kit comes w/ 2 ea. Straight plates & 2 ea. Formed plates, hinge bolts with nuts.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"DOCK FASTENER KIT (Bulk Pkg.)"
- (100 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (100 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(100 ea.) 3/8”; Galvanized Washers.
- per page