Home :: Boat Roller Ramps ( #1 ) :: ( #3 ) Pontoon Ramps :: Pontoon Ramp; DDA-2250; ( 2,000 pound capacity, 19' long )

Pontoon Ramp; DDA-2250; ( 2,000 pound capacity, 19' long )

Pontoon Ramp; DDA-2250; ( 2,000 pound capacity, 19' long )
 Water End View. (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit )  Shore End View. (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) HAPPY Customer, while assembling View. (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Winch End View. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Winch End, 45 Degree View. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Side View. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Water End, 45 Degree View. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Water End View. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Winch End, Close Up View. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) Side View, Close Up. NOT FULLY ASSEMBELED (NOTE: Shown with 2 options, BRA-225-4; 4' Extra Section & BRA-34; Section Disconnect kit ) OPTIONAL, BRA-34; Disc. Kit, Close UP View. NOT FULLY ASSEMBELED (NOTE: Shown with BRA-34; Section Disconnect kit )

The DDA-2250; Pontoon Ramp features 2" Sq. Aluminum tubular construction & 1" x 2" Aluminum Roller Tubes. Basic unit is 19’ long ( 2 ea. 8' Roller Bunk Sections With a 3' Winch Mount Assembly ) and has a maximum load capacity of 2,000 lbs., adjustable to fit round pontoons ONLY. Provides on shore storage for protection against rocky shores, algae, and rough water. May be used for winter storage, out of water on shores free or protected from ice action. Features a 1,800 lb. manual winch & 144 ea. support rollers. All fasteners & small steel assembly parts are Stainless Steel or Galvanized for extra corrosion protection, especially in salt water. 4' or 8’ extra sections can easily be added to Pontoon Boat Roller Ramps, along with other accessories listed below.

NOTE:  CLICK ON "View detailed images" to left, to see large Photo Pictures.

NOTE: This pictured DDA-2250; "Pontoon Ramp" actually has an ( OPTIONAL ) BRA-225; "4 ft. Extra Section" which is added after 1st. 8' section. The 2nd. 8' section is than attached with ( OPTIONAL ) BRA-34; "Disconnect Kit" that allows for last 8' section to be easily taken off for convenient winter storage of Pontoon Boat on 15' of Pontoon Ramp on shore.

NOTE: Proper Pontoon Ramp installation requires ramp to be supported at both ends, each section connecting joint and PREFERABLY by all cross tubes. This can be done by leveling the ground, useing concrete blocks, wood timbers etc. or purchasing BR-20 Support Kits. NOTE: 1 ea. BR-26; "Anchoring Kit" does come with the Pontoon Ramp and is an added plus in anchoring winch mount assembly of ramp to the ground and gives added stability to Boat Ramp. Check out the other Boat Ramp accessories, like an electric winch, all intended to inhance your Boat Ramp product.            

NOTE: NOT RECOMMENDED FOR PONTOON BOATS WITH A EXTENDED CENTER TRANSOM MOTOR MOUNT, WERE THE MOTOR IS MOUNTING TO A TRANSOM THAT ACTUALLY EXTENDS OUT PAST THE END OF THE PONTOONS!! NOTICE the pontoon boat in the picture, the transom motor mount is EVEN with the ends of the pontoons!!

PRODUCT WEIGHT: 290 LBS.

REDUCED SHIPPING CHARGE !!!: $225.00 per DDA-2250 ( In continental U.S. Only, call for other discounts to Alaska or Canada ). ( Normally $400.00 & UP! )DON'T MISS OUT ON REDUCED SHIPPING COST, WHILE THEY LAST !!

 

Accessories:

"TO VIEW ACCESSORIES PHOTOS" ( CLICK HERE ) and go to "ACCESSORIES DETAILS & ORDER PAGEBRA-225; Aluminum 8’ Boat Ramp extra section.

  • BRA-225-4; Aluminum 4’ Boat Ramp extra section.

  • BRA-225; Aluminum 8’ Boat Ramp extra section.

  • BR-20; Support Kit 1 pr. 1 1/4” pipe clamps & 1 pr 1 1/4: base pads (no pipe included).

  • BR-26; Anchoring Kit (2ea. 1 1/4” x 3’ long pipe, 2 augers and brackets and mounting fastener).

  • BR-27; Electric winch Mounting Plate. Fits 2” wide winch post, with fastener (no winch).

  • BR-58; Boat Ramp Installation Wheel Kit. ( 2 ea. 24" dia. wheels, 1 ea. axle, 2 ea. axle mt. brkts. and all mounting hrdw. )

  • BR-358; Electric Winch.

Shipping charges listed on accessories are only effective if item/items are ordered with a Ramp.  Shipping charge doubles if item/items are ordered without a ramp purchase. 

NOTE: YOU MUST CALL VE-VE, INC. FOR THE SHIPPING CHARGES ON THE RAMP AND ANY ITEM LISTED WITHOUT A SHIPPING CHARGE.

Contact VE-VE inc. with any further questions etc. at (763) 427-5330 or Email

9%
Details
SKU DDA-2250
 
Market price: $3,325.00
Our price: $3,025.00
Options
Quantity
: *
: *
: *
Type the characters you see in the picture:


*

Customers' rating

Sign in to rate

Customer's Reviews

There have been no reviews for this product.

Add your review here

: *
: *
Type the characters you see in the picture:


*