- per page
Use "Dock Pipe Wrench" to screw in & out dock pipe with "Pipe Augers" mounted to them from lake/river bottom, or in some cases, to pull out dock pipe W/out Augers.
NOTE: "Auger Wrench" works on 1-1/4", 1-1/2" & 2" Dock Pipe.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
"DOCK FASTENER KIT (Bulk Pkg.)"
- (100 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (100 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(100 ea.) 3/8”; Galvanized Washers.
NOTE:!! D-638-80; MUST ORDER MINIMUM OF 2 EA. FOR ORDER TO PROCEED. SORRY, BUT NEW SHIPPING COST ON THIS OVERLENGTH ITEM PUSHED US TO IMPLEMENT THIS NEW MINIMUM ORDER POLICY.!!
D-638-80; "Dock Stabilizer Kit", NOTE: This is NOT for 4' wide docks!! It is for docks WIDER then 4 ft. & up to 6 ft. (72”) wide, with 2" dock pipe ( 2-3/8" O.D.). Stabilizer bar helps to reduce a docks side to side racking/swaying. U-shapped design mounting brackets allow brackets to be mounted on dock pipes already fastened to dock. ( DOES NOT need to be slid over from the top of the pipe ).
Includes: 1ea. 80" Brace Bar, 2ea. End Mount Brackets & Fasteners.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION and MORE PICTURES )
THIS ITEM IS OUT OF STOCK UNTIL FURTHER NOTICE, SORRY!!
2' "Bumper Mounts" are made to slip over the top of your existing ( 2" pipe, ( 2-3/8" O.D. ) dock posts and mount a Carpeted Wood or Polyethylene Bumper.
NOTE: Shown with optional D-542; "Polyethylene Bumper", bumper pictured below.
NOTE:!! D-638; MUST ORDER MINIMUM OF 2 EA. FOR ORDER TO PROCEED. SORRY, BUT NEW SHIPPING COST ON THIS OVERLENGTH ITEM PUSHED US TO IMPLEMENT THIS NEW MINIMUM ORDER POLICY.!!
D-638; "Dock Stabilizer Kit", for 3 ft. (36”) to 4 ft. (48”) wide docks with 2" dock pipe ( 2-3/8" O.D.). Stabilizer bar helps to reduce a docks side to side racking/swaying. U-shaped design mounting brackets allow brackets to be mounted on dock pipes all ready fastened to dock. ( DOES NOT need to be slid over from the top of the pipe ).
Includes: 1ea. 53" Brace Bar, 2ea. End Mount Brackets & Fasteners.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION and MORE PICTURES )
D-638-40; "Dock Stabilizer Kit" for docks with 2" dock pipe ( 2-3/8" O.D.). Side stabilizer bar helps to reduce a docks front to back racking/swaying. U-shaped design pipe mounting bracket allow bracket to be mounted on dock pipes already fastened to dock. ( NOTE: Angle brace shown on outside to better show angle, NORMALLY mounted to inside ).
Includes: 1ea. 40" Brace Bar, 1ea. Pipe Mount Bracket & 2 ea. Dock Mounting Bars, w/ All Fasteners.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION and MORE PICTURES )
The "Right Outside Corner Bracket" has a 90 degree formed angle iron dock mount ( ties end corner together giving added support ) with adjustable sleeve for fastening 2" dock pipe to dock section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
The "Left Outside Corner Bracket" has a 90 degree formed angle iron dock mount ( ties end corner together giving added support ) with adjustable sleeve for fastening 2" dock pipe to dock section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
The "Inside Corner Bracket" has a angle iron dock mount with adjustable sleeve for fastening 2" dock pipe to dock sections. Used in corners for dual section support or inside (underneath dock) of outside corners to make outside of dock free of dock support pipes.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
The "Base Pad" has a 12" square base and adjustable sleeve to mount 2" Pipe ( 1/2" adjustment bolt included ). Hole in center of pad allows pipe to go through for extra dock support if desired. Usually used 2-4 ea. per dock section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
The "Straight Brkt. / Section Conn." has a angle iron dock mount with adj. sleeve for fastening 2" pipe to dock. Usually used 2 ea. per connection joint for dock support and connecting dock sections together ( 1/2" adj. bolt included ).
( CLICK DETAILS FOR DETAILED PRODUCT INFO. )
The D-506; "Sand Auger" ( For 2" Sch. 40 Pipe, ( 2-1/16" Inside diameter )), mounts in the inside of the dock pipe and stabilizes it firmly to the lake bottom for added dock stability and support. These are not the lightweight / breakable Aluminum ones, these are made of Solid Cast Iron, weighing over 4 lbs. each.
NOTE: THIS ITEM SUBJECT TO A MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINIMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION & INFO. ON AUGER SCREWING WRENCH )
The "Straight Bracket" features an angle iron dock mount with an adjustable sleeve for fastening 2" dock pipe to side of dock section. Usually used 2-4 ea. per dock section. ( 1/2" adjustment bolt included ).
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Pipe Driving Cap" helps protect top of pipe when driving pipe into lake bottom. Cap fits over 1-1/4" Pipe (1-5/8" O.D.), 1-1/2" Pipe (1-7/8" O.D.) & 2" Pipe (2-3/8" O.D.). Hole provided to tie optional retrieving rope and place other end over pipe. NOTE: THIS ITEM SUBECT TO $14.50 MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINUMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
- per page