- per page
D-638-40; "Dock Stabilizer Kit" for docks with 2" dock pipe ( 2-3/8" O.D.). Side stabilizer bar helps to reduce a docks front to back racking/swaying. U-shaped design pipe mounting bracket allow bracket to be mounted on dock pipes already fastened to dock. ( NOTE: Angle brace shown on outside to better show angle, NORMALLY mounted to inside ).
Includes: 1ea. 40" Brace Bar, 1ea. Pipe Mount Bracket & 2 ea. Dock Mounting Bars, w/ All Fasteners.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION and MORE PICTURES )
NOTE:!! D-638-80; MUST ORDER MINIMUM OF 2 EA. FOR ORDER TO PROCEED. SORRY, BUT NEW SHIPPING COST ON THIS OVERLENGTH ITEM PUSHED US TO IMPLEMENT THIS NEW MINIMUM ORDER POLICY.!!
D-638-80; "Dock Stabilizer Kit", NOTE: This is NOT for 4' wide docks!! It is for docks WIDER then 4 ft. & up to 6 ft. (72”) wide, with 2" dock pipe ( 2-3/8" O.D.). Stabilizer bar helps to reduce a docks side to side racking/swaying. U-shapped design mounting brackets allow brackets to be mounted on dock pipes already fastened to dock. ( DOES NOT need to be slid over from the top of the pipe ).
Includes: 1ea. 80" Brace Bar, 2ea. End Mount Brackets & Fasteners.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION and MORE PICTURES )
NOTE:!! D-638; MUST ORDER MINIMUM OF 2 EA. FOR ORDER TO PROCEED. SORRY, BUT NEW SHIPPING COST ON THIS OVERLENGTH ITEM PUSHED US TO IMPLEMENT THIS NEW MINIMUM ORDER POLICY.!!
D-638; "Dock Stabilizer Kit", for 3 ft. (36”) to 4 ft. (48”) wide docks with 2" dock pipe ( 2-3/8" O.D.). Stabilizer bar helps to reduce a docks side to side racking/swaying. U-shaped design mounting brackets allow brackets to be mounted on dock pipes all ready fastened to dock. ( DOES NOT need to be slid over from the top of the pipe ).
Includes: 1ea. 53" Brace Bar, 2ea. End Mount Brackets & Fasteners.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION and MORE PICTURES )
"Pipe Driving Cap" helps protect top of pipe when driving pipe into lake bottom. Cap fits over 1-1/4" Pipe (1-5/8" O.D.), 1-1/2" Pipe (1-7/8" O.D.) & 2" Pipe (2-3/8" O.D.). Hole provided to tie optional retrieving rope and place other end over pipe. NOTE: THIS ITEM SUBECT TO $14.50 MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINUMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
THE D-56; 2" PIPE CAPS ARE CURRENTLY OUT OF STOCK.
,
The "Pipe Cap" fits over 2" dock pipe that is 2-3/8" O.D. These round injection molded pipe caps are made with marine grade vinyl and fit snugly over the top of the pipe for a safe and attractive finish.
NOTE: BECAUSE OF LOW INVENTORY AT THIS TIME, PIPE CAPS WILL ONLY BE SOLD ALONG WITH A DOCK BRACKET ORDER, SORRY!!
Shipping is FREE when ordered with a dock bracket order!!!!
"DOCK FASTENER KIT (Bulk Pkg.)"
- (100 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (100 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(100 ea.) 3/8”; Galvanized Washers.
"FASTENER KIT"
- (4 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (4 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(4 ea.) 3/8”; Galvanized Washers.
Use "Dock Pipe Wrench" to screw in & out dock pipe with "Pipe Augers" mounted to them from lake/river bottom, or in some cases, to pull out dock pipe W/out Augers.
NOTE: "Auger Wrench" works on 1-1/4", 1-1/2" & 2" Dock Pipe.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
The D-506; "Sand Auger" ( For 2" Sch. 40 Pipe, ( 2-1/16" Inside diameter )), mounts in the inside of the dock pipe and stabilizes it firmly to the lake bottom for added dock stability and support. These are not the lightweight / breakable Aluminum ones, these are made of Solid Cast Iron, weighing over 4 lbs. each.
NOTE: THIS ITEM SUBJECT TO A MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINIMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION & INFO. ON AUGER SCREWING WRENCH )
THIS ITEM IS OUT OF STOCK UNTIL FURTHER NOTICE, SORRY!!
2' "Bumper Mounts" are made to slip over the top of your existing ( 2" pipe, ( 2-3/8" O.D. ) dock posts and mount a Carpeted Wood or Polyethylene Bumper.
NOTE: Shown with optional D-542; "Polyethylene Bumper", bumper pictured below.
The D-562; "Rectangular Backing Plate" can be used with the D-550-L, D-555-L & D-556-L "Straight Brkt., Section Connectors" as a back up plate on inside of dock section to add more bracket mounting support ( 2 ea. per bracket ).
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
The "Straight Brkt. / Section Conn." has a angle iron dock mount with adj. sleeve for fastening 2" pipe to dock. Usually used 2 ea. per connection joint for dock support and connecting dock sections together ( 1/2" adj. bolt included ).
( CLICK DETAILS FOR DETAILED PRODUCT INFO. )
The "Base Pad" has a 12" square base and adjustable sleeve to mount 2" Pipe ( 1/2" adjustment bolt included ). Hole in center of pad allows pipe to go through for extra dock support if desired. Usually used 2-4 ea. per dock section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
The D-562; "Rectangular Backing Plate" can be used with the D-560 & D-565 "O.S. Corner Brackets" as a back up plate on inside of dock section or the D-566; "I.S. Corner Bracket on the outside of dock to add more bracket mounting support. ( 2 ea. per Bracket ).
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
- per page