- per page
THIS ITEM IS OUT OF STOCK.
,The D-506; "Sand Auger" ( For 2" Sch. 40 Pipe, ( 2-1/16" Inside diameter )), mounts in the inside of the dock pipe and stabilizes it firmly to the lake bottom for added dock stability and support. These are not the lightweight / breakable Aluminum ones, these are made of Solid Cast Iron, weighing over 4 lbs. each.
NOTE: THIS ITEM SUBJECT TO A MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINIMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION & INFO. ON AUGER SCREWING WRENCH )
THE D-56; 2" PIPE CAPS ARE CURRENTLY OUT OF STOCK.
,
The "Pipe Cap" fits over 2" dock pipe that is 2-3/8" O.D. These round injection molded pipe caps are made with marine grade vinyl and fit snugly over the top of the pipe for a safe and attractive finish.
NOTE: BECAUSE OF LOW INVENTORY AT THIS TIME, PIPE CAPS WILL ONLY BE SOLD ALONG WITH A DOCK BRACKET ORDER, SORRY!!
Shipping is FREE when ordered with a dock bracket order!!!!
THIS ITEM IS OUT OF STOCK.
,"Pipe Driving Cap" helps protect top of pipe when driving pipe into lake bottom. Cap fits over 1-1/4" Pipe (1-5/8" O.D.), 1-1/2" Pipe (1-7/8" O.D.) & 2" Pipe (2-3/8" O.D.). Hole provided to tie optional retrieving rope and place other end over pipe. NOTE: THIS ITEM SUBECT TO $14.50 MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINUMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
THIS ITEM IS OUT OF STOCK.
,The D3-480-2A; "Dock Ramp Hinge Kit" for T-Layout Ramp, is used when the Dock Ramp ( or Hinged Section ) is narrower then the section it is mounted to & will NOT be mounted even on the right or left side of the adjoining section ( Thus making a T-layout ). Ramp Kit comes w/ 2 ea. Straight plates & 2 ea. Formed plates, hinge bolts with nuts.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,The D3-480-1A; "Dock Ramp Hinge Kit" for L-Layout Ramp, is used when the Dock Ramp ( or Hinged Section ) is narrower then the section it is mounted to, but will be mounted even on the right or left side of the adjoining section ( Thus making a L-Layout ). Ramp Kit comes w/ 3 ea. Straight plates & 1 ea. Formed plate, hinge bolts with nuts.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
D3-464; "Hitch Pin & Hitch Clip" ( 1 of Each). The Hitch Pin is 5/8" Dia. & the Hitch Clip is ( .148" Diam. Material ). These items are used on our D3-420 & D3-430 "Floating Dock, Section Connectors" also on the D3-486; "Corner Support Bar Assembly".
NOTE: The Hitch pin diameter is 5/8", if not used on a VE-VE Inc. manufactured floating dock bracket, make sure what you are replacing is 5/8" diameter. Other manufactures hitch pins may be smaller ( 1/2" diameter ) or larger ( 3/4" diameter ). ALSO, the effective length ( distance from form to inside of hole ) is 2-1/2" !!
"DOCK FASTENER KIT (Bulk Pkg.)"
- (100 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (100 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(100 ea.) 3/8”; Galvanized Washers.
"FASTENER KIT"
- (4 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (4 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(4 ea.) 3/8”; Galvanized Washers.
"Cement Anchor Cleats" are cemented into a 5 gallon pail or any cement form to make an anchor used to attach to and stabilize Floating Docks that do not have guide pipes. Price is for 4 ea. pc's.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
"Dock Ramp Roller Assembly" is used on end of Hinged Ramps to allow end of dock ramp to roll on other dock section or shore when Floating Dock height changes.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Section Tie Plates" are used to connect 2 ea. dock sections together. Use 2 ea. PER SIDE if sections are open ended, use 1 ea. with 2 ea. D3-435; "Inside Corner Supports" or 2 ea. D3-442; "Square Backing Plates" PER SIDE if secton ends are closed.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Dock Ramp Hinge Kit" ( for Straight-Layout Ramp ), is used for the first dock section ( RAMP ) when the shore level is higher or lower than the main dock or when useing a ramp to transition from one dock level to another. Kit includes 4 ea. Hinge Plates & 2 ea. Hinge Bolts W/ Nuts.
For D3-480-1A; Ramp Hinge Kit, for L-Layout Ramp ( CLICK HERE ) to see.
For D3-480-2A; Ramp Hinge Kit, for T-Layout Ramp ( CLICK HERE ) to see.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS CURRENTLY OUT OF STOCK, ANOTHER PRODUCTION RUN IS AT THE GALVANIZERS, SO STILL TAKING ORDERS!! SORRY!! PROJECTED SHIP DATE IS 11/20-30/23, YOUR PATIENCE WILL BE REWARDED W/ A QUALITY AMERICAN MADE PRODUCT!!
"Chain Retainer" bolts to side of dock to fasten / mount chain that is connected at other end to a submerged weight that holds dock in place.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Inside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie inside corner of 2 dock sections together & stabilize inside corner of both sections. Same parts as D-441; "Outside Corner Angle Tie" ( Shown Above ), but Pipe Sleve is welded to the inside of the formed corner piece.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
- per page