- per page
THIS ITEM IS OUT OF STOCK.
,The D-506; "Sand Auger" ( For 2" Sch. 40 Pipe, ( 2-1/16" Inside diameter )), mounts in the inside of the dock pipe and stabilizes it firmly to the lake bottom for added dock stability and support. These are not the lightweight / breakable Aluminum ones, these are made of Solid Cast Iron, weighing over 4 lbs. each.
NOTE: THIS ITEM SUBJECT TO A MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINIMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION & INFO. ON AUGER SCREWING WRENCH )
"FASTENER KIT"
- (4 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (4 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(4 ea.) 3/8”; Galvanized Washers.
"DOCK FASTENER KIT (Bulk Pkg.)"
- (100 ea.) 3/8”-16 x 2-1/2”; Galvanized Carriage Bolts.
- (100 ea.) 3/8”-16; Galvanized Hex Nuts.
-
(100 ea.) 3/8”; Galvanized Washers.
THE D-56; 2" PIPE CAPS ARE CURRENTLY OUT OF STOCK.
,
The "Pipe Cap" fits over 2" dock pipe that is 2-3/8" O.D. These round injection molded pipe caps are made with marine grade vinyl and fit snugly over the top of the pipe for a safe and attractive finish.
NOTE: BECAUSE OF LOW INVENTORY AT THIS TIME, PIPE CAPS WILL ONLY BE SOLD ALONG WITH A DOCK BRACKET ORDER, SORRY!!
Shipping is FREE when ordered with a dock bracket order!!!!
THIS ITEM IS OUT OF STOCK.
,"Pipe Driving Cap" helps protect top of pipe when driving pipe into lake bottom. Cap fits over 1-1/4" Pipe (1-5/8" O.D.), 1-1/2" Pipe (1-7/8" O.D.) & 2" Pipe (2-3/8" O.D.). Hole provided to tie optional retrieving rope and place other end over pipe. NOTE: THIS ITEM SUBECT TO $14.50 MINIMUM SHIPPING CHARGE. IF TOTAL ORDER SHIPPING CHARGES DO NOT ACHIEVE MINUMUM.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION )
"T-Section Connector" ( 1 ea. Male & 1 ea. Female Connector Bracket, set also includes 1 ea. hitch pin & 1 ea. hitch clip ). Use to connect 2 floating dock sections together. 2 sets required to connect 2 sections together.
NOTE: If using D3-442; "Backing Plates" OR D-561; "Fastener Kits" with the D3-420, you need 2 of either one per 1 ea. D3-420; "T-Section Connector"!!
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Corner Tie Section Connector" ( 1 ea. Male & 1 ea. Female Connector Bracket, set also includes 1 ea. hitch pin & 1 ea. hitch clip ). Use to connect 2 floating dock sections while also tying together corners of the dock sections. 2 sets required to connect 2 sections together.
NOTE: If using D3-435; "Inside Corner Supports" OR D-561; "Fastener Kits" with the D3-430, you need 2 ea. D3-435 or 4 ea. D-561 per 1 ea. D3-430; "Corner Tie Section Connector"!!
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Inside Corner Support" can be used with the D3-430, D3-440 & D3-441.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Inside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie inside corner of 2 dock sections together & stabilize inside corner of both sections. Same parts as D-441; "Outside Corner Angle Tie" ( Shown Above ), but Pipe Sleve is welded to the inside of the formed corner piece.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Outside Corner Angle Tie" can be used with D3-435 "Inside Corner Support" or when a float is in the way the D3-442; Square Backing Plate" may be used.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION; PIPE CAPS AND FASTENERS )
"Outside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie corner of dock end section together & stabilize a floating end section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Square Backing Plate" can be used with the D3-420 "T-Section Connectors" & most other D3-400 series brackets as a back up plate on inside of dock section for added bracket support.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Stringer Angle Bracket" is used for inside dock section stringers.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Backup Washer Bar" can be used with the D3-444 "Stringer Angle Bracket" or the D3-459; "Dock Ramp Roller Assembly".
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
- per page
