- per page
"T-Section Connector" ( 1 ea. Male & 1 ea. Female Connector Bracket, set also includes 1 ea. hitch pin & 1 ea. hitch clip ). Use to connect 2 floating dock sections together. 2 sets required to connect 2 sections together.
NOTE: If using D3-442; "Backing Plates" OR D-561; "Fastener Kits" with the D3-420, you need 2 of either one per 1 ea. D3-420; "T-Section Connector"!!
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Square Backing Plate" can be used with the D3-420 "T-Section Connectors" & most other D3-400 series brackets as a back up plate on inside of dock section for added bracket support.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Corner Tie Section Connector" ( 1 ea. Male & 1 ea. Female Connector Bracket, set also includes 1 ea. hitch pin & 1 ea. hitch clip ). Use to connect 2 floating dock sections while also tying together corners of the dock sections. 2 sets required to connect 2 sections together.
NOTE: If using D3-435; "Inside Corner Supports" OR D-561; "Fastener Kits" with the D3-430, you need 2 ea. D3-435 or 4 ea. D-561 per 1 ea. D3-430; "Corner Tie Section Connector"!!
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Inside Corner Support" can be used with the D3-430, D3-440 & D3-441.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Outside Corner Angle Tie" can be used with D3-435 "Inside Corner Support" or when a float is in the way the D3-442; Square Backing Plate" may be used.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION; PIPE CAPS AND FASTENERS )
"Stringer Angle Bracket" is used for inside dock section stringers.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Backup Washer Bar" can be used with the D3-444 "Stringer Angle Bracket" or the D3-459; "Dock Ramp Roller Assembly".
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Floating Straight Bracket", W/ Ring Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to stabilize floating docks or use bracket as a tie off for anchoring floating docks or swim rafts.
( CLICK ON DETAILS FOR DETAILED PRODUCT DESCRIPTION; PIPE CAPS AND FASTENERS )
"Floating Straight Bracket", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to stabilize floating docks or use bracket as a tie off for anchoring floating docks or swim rafts.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Outside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie corner of dock end section together & stabilize a floating end section.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Inside Corner Angle Tie", W/ Pipe Sleeve works with dock pipe UP TO 2" ( 2-3/8" O.D. ) to Tie inside corner of 2 dock sections together & stabilize inside corner of both sections. Same parts as D-441; "Outside Corner Angle Tie" ( Shown Above ), but Pipe Sleve is welded to the inside of the formed corner piece.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS CURRENTLY OUT OF STOCK, ANOTHER PRODUCTION RUN IS AT THE GALVANIZERS, SO STILL TAKING ORDERS!! SORRY!! PROJECTED SHIP DATE IS 11/20-30/23, YOUR PATIENCE WILL BE REWARDED W/ A QUALITY AMERICAN MADE PRODUCT!!
"Chain Retainer" bolts to side of dock to fasten / mount chain that is connected at other end to a submerged weight that holds dock in place.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
THIS ITEM IS OUT OF STOCK.
,"Dock Ramp Hinge Kit" ( for Straight-Layout Ramp ), is used for the first dock section ( RAMP ) when the shore level is higher or lower than the main dock or when useing a ramp to transition from one dock level to another. Kit includes 4 ea. Hinge Plates & 2 ea. Hinge Bolts W/ Nuts.
For D3-480-1A; Ramp Hinge Kit, for L-Layout Ramp ( CLICK HERE ) to see.
For D3-480-2A; Ramp Hinge Kit, for T-Layout Ramp ( CLICK HERE ) to see.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION; PIPE CAPS AND FASTENERS )
"Section Tie Plates" are used to connect 2 ea. dock sections together. Use 2 ea. PER SIDE if sections are open ended, use 1 ea. with 2 ea. D3-435; "Inside Corner Supports" or 2 ea. D3-442; "Square Backing Plates" PER SIDE if secton ends are closed.
( CLICK ON DETAILS FOR DETAILED PRODUCT DISCRIPTION AND FASTENERS )
- per page
